+7 (812) 309 34 73. Договоримся!
Общая информация (PWR-C45-1300ACV)
PWR-C45-1300ACV is a Cisco Catalyst Switch 4500 Series Switch Power Supply, delivering 1300W AC power (Data and PoE) for Cisco 4500 switches. Notice that PWR-C45-1300ACV= is similar with PWR-C45-1300ACV, except that PWR-C45-1300ACV= is a spare one.
Быстрые спецификации
Table 1.
|
Product Code |
PWR-C45-1300ACV |
|
Manufacturer |
Cisco System Inc. |
|
Product Type |
Power Supply Module |
|
Compatible product |
Cisco Catalyst 4500-E Series Switches and classic chassis |
|
Power Input |
Up to 1300W AC Power and 800W PoE Power |
|
Auto-Sensing |
110V (16A) / 220V (7A) |
|
Rated MTBF (Hours) |
164,220 |
Детали продукта
Figure 1. PWR-C45-1300ACV can be installed in the Catalyst 4500 switch Chassis.
Compatible Products
Table 2. Recommended Compatible Switches.
|
Model |
Description |
|
WS-C4503-E |
Cat4500 E-Series 3-Slot Chassis, fan, no ps |
|
WS-C4507R-E |
Cat4500 E-Series 7-Slot Chassis, fan, no ps, Red Sup Capable |
|
WS-C4510R-E |
Cat4500 E-Series 10-Slot Chassis, fan, no ps,Red Sup Capable |
|
WS-C4507R+E |
Catalyst 4500E 7 slot chassis for 48Gbps/slot - Supervisor Engine redundancy - Power redundancy |
|
WS-C4506-E |
Catalyst 4500 E-Series 6-Slot Chassis, fan, no ps |
Сравнение с аналогом
Table 3. Comparison of similar item.
|
Product Code |
PWR-C45-1400AC |
PWR-C45-1300ACV |
|
Manufacturer |
Cisco System Inc. |
Cisco System Inc. |
|
Product Type |
Power Supply Module |
Power Supply Module |
|
Compatible product |
Cisco Catalyst 4500-E Series Switches and classic chassis |
Cisco Catalyst 4500-E Series Switches and classic chassis |
|
Power Input |
1400W AC (Data Only) |
Up to 1300W AC Power and 800W PoE Power |
|
Rated MTBF (Hours) |
570,530 |
164,220 |
Что бы получить больше информации
У вас есть какие-либо вопросы о PWR-C45-1300ACV?
Свяжитесь с нами через ЧАТ или e-mail: info@itg-spb.ru.
| Specification | |
| INPUT OK | Green—Source AC voltage is OK. (Input voltage is 85 VAC or greater.) Off—Source AC voltage falls below 70 VAC, is not present, or the power supply is turned off. |
| Power over Ethernet (PoE) | Supported, up to 800 W (211 Cisco phones in combined mode) |
| Branch circuit requirement | Each chassis power supply should have its own dedicated, fused-branch circuit: For North America—15 A or 20 A For International—Circuits sized to local and national codes All Catalyst 4500 E-series AC-input power supplies require single-phase source AC. All AC power supply inputs are fully isolated. – Source AC can be out of phase between multiple power supplies in the same chassis, which means that PS1 can be operating from phase A and PS2 can be operating from phase B. – For high-line operation, the power supply operates with the hot conductor wired to a source AC phase and the neutral conductor wired either to ground or to another source AC phase as long as the net input voltage is in the range of 170 to 264 VAC. – Source AC can be out of phase between AC inputs on power supplies that are equipped with multiple AC inputs, which means that power cord 1 can be plugged into phase A and power cord 2 can be plugged into phase B. |
| AC-input type | Autoranging input with power factor corrector Note Power factor correction is a standard feature on all Catalyst 4500 E-series AC-input power supplies. PFC reduces the reactive component in the source AC current allowing higher power factors (typically 99 percent or better) and lower harmonic current components. |
| AC-input voltage | Low-line (120 VAC nominal)—85 VAC (min) to 132 VAC (max) High-line (230 VAC nominal)—170 VAC (min) to 264 VAC (max) |
| AC-input current | 16 A @ 100 VAC 7 A @ 240 VAC |
| AC-input frequency | 50/60 Hz (nominal) (±3 Hz for full range) |
| Power supply output | 84.7 A @ 12 V @ (data) 12.5 A @ 3.3 V (data) 16.7 A @ –50 V (PoE) |
| Power supply output capacity | 1300 W maximum 1050 W+ 40 W redundant mode (data) 1667 W maximum in combined mode (data) 800 W maximum each in redundant mode (PoE) 1333 W maximum in combined mode (PoE) |
| Maximum kVA rating | 1.76 kVA |
| Output holdup time | 20 ms minimum |
| Max heat dissipation | 1568 BTUs/hr |
| Minimum software requirement | Cisco IOS Release 12.1(12c)EW |
| FAN OK | Green—Power supply fan is operating properly. Off—Power supply fan failure is detected. |
| OUTPUT FAIL | Red—Problem with one or more of the DC-output voltages of the power supply is detected. Off—DC-output voltage with acceptable margins. Note For proper operation of the OUTPUT FAIL LED, systems with single power supplies must be configured with a minimum of one fan tray assembly and one supervisor engine. Systems with dual power supplies must have a minimum configuration of one fan tray assembly, one supervisor engine, and one additional module. Failure to meet these minimum configuration requirements can cause a false power supply output fail signal. |
Теги: PWR-C45-1300ACV Cisco