+7 (812) 309 34 73. Договоримся!
Общая информация (WS-X45-SUP7-E)
WS-X45-SUP7-E, the Cisco Catalyst 4500E supervisor engine 7-E, is the leading borderless networks access and aggregation supervisor engine for the Cisco Catalyst 4500E series. Supervisor Engine7-E delivers high-performance aggregation deployments with increasing Gigabit Ethernet and 10G Ethernet fiber density along with hardware capabilities to support enterprise-level aggregation functions.
Notice that WS-X45-SUP7-E= is similar with WS-X45-SUP7-E, except that WS-X45-SUP7-E= is a spare one.
Быстрые спецификации
Figure 1. WS-X45-SUP7-E Appearance.
Table 1.
|
Product Code |
WS-X45-SUP7-E |
|
Centralized switching capacity |
848 Gbps |
|
Per-slot switching capacity |
48 Gbps |
|
Throughput |
250 Mpps for IPv4 125 Mpps for IPv6 250 Mpps for L2 Bridging |
|
IPv4 routing entries |
256,000 |
|
IPv6 routing entries |
128,000 |
|
Multicast routes |
16,000 (available with Cisco IOS XE 3.1.0 SG) 32,000 (Available with Cisco IOS XE 3.2.0 SGlater) |
|
CPU |
Dual core; 1.5 GHz |
|
CPU queues |
64 |
|
Synchronous dynamic RAM (SDRAM) |
2 GB upgradable to 4 GB |
|
Nonvolatile RAM (NVRAM) |
1 GB |
|
Security and QoS hardware entries |
128,000 |
|
Cisco Network Admission Control (NAC) andDynamic Host Configuration Protocol (DHCP) snooping entries |
12,000 |
|
MAC addresses |
55,000 |
|
Active VLANs |
4,094 |
|
Address Resolution Protocol (ARP) entries |
47,000 |
|
Spanning Tree Protocol instances |
10,000 |
|
Switched virtual interfaces (SVIs) |
4,094 |
|
Switched Port Analyzer (SPAN) |
Maximum of 8 sessions: ingressegress |
Детали продукта
Figure 2. WS-X45-SUP7-E can be installed in the Catalyst 4500 switch Chassis.
Figure 3. WS-X45-SUP7-E Front Panel.
Note:
? STATUS LED ? Reset Button ? ACTIVE SUP LED ? UTILIZATION LED ? USB Ports ? Secure Digital Port ? Console Port
? 10/100/1000 MGT Port ? 4 × 1G/10G Uplinks SFP/SFP+
Table 2. Recommended Cisco Catalyst 4500E Series Line Cards and Modules.Supported Line Cards and Modules
|
Model |
Description |
|
WS-X4748-UPOE+E |
Cisco Catalyst 4500E Series, 48-port 802.3af PoE, 802.3at PoEP, and UPoE 10/100/1000 |
|
WS-X4748-RJ45V+E |
Cisco Catalyst 4500E Series, 48-port PoE 802.3at 10/100/1000 (RJ-45) |
|
WS-X4712-SFP+E |
Cisco Catalyst 4500E Series, 12-port 10 Gigabit Ethernet (SFP+) |
|
WS-X4748-SFP-E |
Cisco Catalyst 4500E Series 48-port Gigabit Ethernet (SFP) |
|
WS-X4724-SFP-E |
Cisco Catalyst 4500E Series 24-port Gigabit Ethernet (SFP) |
|
WS-X4712-SFP-E |
Cisco Catalyst 4500E Series 12-port Gigabit Ethernet (SFP) |
|
WS-X4648-RJ45V-E |
Cisco Catalyst 4500E Series, 48-port 802.3af PoE 10/100/1000 (RJ-45) |
|
WS-X4648-RJ45V+E |
Cisco Catalyst 4500E Series, 48-port Premium PoE 10/100/1000 (RJ-45) |
|
WS-X4648-RJ45-E |
Cisco Catalyst 4500E Series, 48-port 10/100/1000 (RJ-45) |
|
WS-X4606-X2-E |
Cisco Catalyst 4500E Series, 6-port 10 Gigabit Ethernet (X2) |
|
WS-X4624-SFP-E |
Cisco Catalyst 4500E Series, 24-port Gigabit Ethernet (SFP) |
|
WS-X4612-SFP-E |
Cisco Catalyst 4500E Series 12-port Gigabit Ethernet (SFP) |
Datasheet Download
Cisco 4500 Switch Modules Datasheet.pdf
Что бы получить больше информации
У вас есть какие-либо вопросы о WS-X45-SUP7-E?
Свяжитесь с нами через ЧАТ или e-mail: info@itg-spb.ru.
| Specification | |
| Humidity (RH) ambient (noncondensing) | 10 to 90% |
| MGT port | Indicates the status of the 10/100/1000BASE-T Ethernet management port Green—The link is operational. Orange—The link is disabled by user. Flashing orange—The power-on self-test indicates a faulty port. Off—No signal is detected or there is a link configuration failure. |
| Uplink link | Indicates the status of the uplink port Green—The link is operational. Orange—The link is disabled by user. Flashing orange—The power-on self-test indicates a faulty port. Off—No signal is detected or there is a link configuration failure. |
| Memory | 2-GB (upgrade to 4-GB) |
| Software requirements (minimum) | Refer to your software release notes for the latest software release requirements |
| Chassis slot restrictions | •Catalyst 4503-E: Slot 1 only •Catalyst 4506-E: Slot 1 only •Catalyst 4507R-E and Catalyst 4507R+E: Slot 3 and slot 4 •Catalyst 4510R-E and Catalyst 4510R+E: Slot 5 and slot 6 |
| Operating temperature | Certified for operation: 32° to 104°F (0° to 40°C) •Designed and tested for operation: 32° to 130°F (0° to 55°C) |
| Bandwidth per slot | 48-Gbps |
| STATUS LED | The status LED indicates the current health of the supervisor engine and the current software state. |
| RESET switch | The RESET switch is used to reset and restart the switch. Note Use a paper clip or other small, pointed object to press the RESET switch. |
| Chassis compatibility | All Catalyst 4500 E-series switches |
| ACTIVE SUP LED | The active supervisor engine LED indicates whether the supervisor engine is active or in standby mode in redundant supervisor engine configurations. |
| UTILIZATION LEDs | Eight LEDs indicate (as an approximate percentage) the current traffic load over the backplane. |
| USB connectors | Two USB 2.0 ports are provided. Port 1 operates in device mode (upstream) and port 2 in host mode (downstream). Port 1 has a standard Type B USB connector and can be used as a USB console.Port 2 has a USB type A connector and a standard USB 2.0 device like a flash memory device can plug into this connector. |
| CONSOLE port | This is a 10/100/1000 port that uses an RJ-45 connector. The console port allows you th access the switch either locally (with a console terminal) has an RJ-45 connector. The console port allows you to perform the following functions: •Configure the switch from the CLI •Monitor network statistics and errors •Configure SNMP agent parameters |
| LINK LED | The 10/100/1000 MGT port has a link LED associated with it. |
| 10/100/1000 MGT port | The Ethernet management port is a Layer 3 host port to which you can connect a PC. You can use the Ethernet management port instead of the switch console port for network management. When managing a switch, connect the PC to the Ethernet management port on a Catalyst 4500 E-series switch. Note When connecting a PC to the Ethernet management port, you must assign an IP address. |
| SECURE DIGITAL slot | A standard Secure Data (SD) memory card interface is provided on the front panel |
| 1G/10G UPLINKS (SFP/SFP+) ports | The Supervisor Engine 7-E has four 1-G or 10-G ports that use either SFP transceivers or SFP+ transceivers. |
| Uplink port LEDs | Each of the four uplink ports has two LEDs associated with it. One LED displays port status when a 1-GB SFP transceiver is installed in the port socket. The second LED displays uplink port status when a 10-GB SFP+ transceiver is installed in the port socket. |
| STATUS | The STATUS LED indicates the status of he supervisor engine. Green—All diagniostic tests have passed Orange—System boot or a diagnostic test is in progress. Red—A diagnostic test failed. Off—The supervisor engine is disabled or is not powered up. |
| Power requirement | 302 W |
| ACTIVE SUP | Indicates whether the supervisor engine is active or standby. Green—Supervisor engine is active (in redundant supervisor engine configurations) Off—Supervisor engine is in standby mode (in redundant supervisor engine configurations) |
| UTILIZATION | When the switch is operational, the eight utilization LEDs indicate the current traffic load over the backplane as an approximate percentage value. Each LED lit green indicates approximately 12.5 percent of load. |
| Operating altitude | Certified for operation: 0 to 6500 ft (0 to 2000 m) •Designed and tested for operation: -200 to 10,000 ft (-60 to 3000 m) |
Теги: WS-X45-SUP7-E Cisco