+7 (812) 309 34 73. Договоримся!
Общая информация (WS-X45-SUP7L-E)
WS-X45-SUP7L-E, the Cisco Catalyst 4500E supervisor engine 7L-E, is the leading borderless networks access and aggregation supervisor engine for the Cisco Catalyst 4500E series. Best-In-Class resiliency feature improves the network reliability and allows supervisor-engine redundancy to prevent network outage when integrates with Cisco catalyst 4507R-E, 4507R+E, 4510R+E4510R-E chassis.
Notice that WS-X45-SUP7L-E= is similar with WS-X45-SUP7L-E, except that WS-X45-SUP7L-E= is a spare one.
Быстрые спецификации
Figure 1. WS-X45-SUP7L-E Appearance.
Table 1.
|
Product Code |
WS-X45-SUP7L-E |
|
Centralized switching capacity |
520 Gbps |
|
Per-slot switching capacity |
48 Gbps |
|
Throughput |
225 Mpps for IPv4 110 Mpps for IPv6 225 Mpps for L2 Bridging |
|
IPv4 routing entries |
64,000 |
|
IPv6 routing entries |
32,000 |
|
Multicast routes |
32,000 |
|
CPU |
Dual core; 1.5 GHz |
|
CPU queues |
64 |
|
Synchronous Dynamic RAM (SDRAM) |
2 GB |
|
Boot flash |
1G |
|
Security and QoS hardware entries |
64,000 |
|
Dynamic Host Configuration Protocol (DHCP) snooping entries |
12,000 |
|
Cisco Network Admission Control (NAC) |
4,000 |
|
MAC addresses |
55,000 |
|
Active VLANs |
4,094 |
|
Address Resolution Protocol (ARP) entries |
47,000 |
|
Spanning Tree Protocol instances |
12,000 |
|
Switched virtual interfaces (SVIs) |
4,094 |
|
SPAN |
8 bidirectional sessions (ingress and egress) |
Детали продукта
Figure 2. WS-X45-SUP7L-E can be installed in the Catalyst 4500 switch Chassis.
Figure 3. WS-X45-SUP7L-E Front Panel.
Note:
? STATUS LED ? Reset Button ? ACTIVE SUP LED ? UTILIZATION LED ? USB Ports ? Secure Digital Port ? Console Port
? 10/100/1000 MGT Port ? 4 × 1G/10G Uplinks SFP/SFP+
Supported Line Cards and Modules
Table 2. Recommended Cisco Catalyst 4500E Series Line Cards and Modules.
|
Model |
Description |
|
WS-X4748-UPOE+E |
Cisco Catalyst 4500E Series, 48-port 802.3af PoE, 802.3at PoEP, and UPoE 10/100/1000 |
|
WS-X4748-RJ45V+E |
Cisco Catalyst 4500E Series, 48-port PoE 802.3at 10/100/1000 (RJ-45) |
|
WS-X4712-SFP+E |
Cisco Catalyst 4500E Series, 12-port 10 Gigabit Ethernet (SFP+) |
|
WS-X4648-RJ45V+E |
Cisco Catalyst 4500E Series, 48-port Premium PoE 10/100/1000 (RJ-45) |
|
WS-X4648-RJ45-E |
Cisco Catalyst 4500E Series, 48-port 10/100/1000 (RJ-45) |
|
WS-X4606-X2-E |
Cisco Catalyst 4500E Series, 6-port 10 Gigabit Ethernet (X2) |
|
WS-X4624-SFP-E |
Cisco Catalyst 4500E Series, 24-port Gigabit Ethernet (SFP) |
|
WS-X4612-SFP-E |
Cisco Catalyst 4500E Series 12-port Gigabit Ethernet (SFP) |
Datasheet Download
Cisco 4500 Switch Modules Datasheet.pdf
Что бы получить больше информации
У вас есть какие-либо вопросы о WS-X45-SUP7L-E?
Свяжитесь с нами через ЧАТ или e-mail: info@itg-spb.ru.
| Specification | |
| Software requirements (minimum) | Refer to your software release notes for the latest software release requirements. |
| Chassis slot restrictions | •Catalyst 4503-E: Slot 1 only •Catalyst 4506-E: Slot 1 only •Catalyst 4507R-E and Catalyst 4507R+E: Slot 3 and slot 4 |
| Bandwidth per slot | 48-Gbps |
| STATUS LED | The STATUS LED indicates the current health of the supervisor engine and the current software state. •Green—All diagnostic tests have passed. •Orange—System boot or a diagnostic test is in progress. •Red—A diagnostic test failed. •Off—The supervisor engine is disabled or is not powered up. |
| RESET switch | The RESET switch is used to reset and restart the switch. Note Use a paper clip or other small, pointed object to press the RESET switch. |
| Chassis compatibility | The Supervisor Engine 7L-E is supported on the Catalyst 4503-E, Catalyst 4506-E, Catalyst 4507R-E, and the Catalyst 4507R+E switch chassis. The Supervisor Engine 7L-E is not supported on the Catalyst 4510R-E or the Catalyst 4510R+E switch chassis. |
| ACTIVE SUP LED | The ACTIVE SUP LED indicates whether the supervisor engine is active or in standby mode in redundant supervisor engine configurations. •Green—Supervisor engine is active (in redundant supervisor engine configurations). •Off—Supervisor engine is in standby mode (in redundant supervisor engine configurations). |
| UTILIZATION LEDs | When the switch is operational, the eight UTILIZATION LEDs indicate the current traffic load over the backplane as an approximate percentage value. Each LED represents approximately 12.5 percent of load. |
| USB connectors | Two USB 2.0 ports are provided: •Port 1 is not supported at this time. •Port 2 operates in host mode (downstream). It has a USB type A connector and a standard USB 2.0 device such as a flash memory device, can plug into this connector. |
| UPLINK (SFP/SFP+) ports | The Supervisor Engine 7L-E has four uplink ports. Ports 1 and 2 support either 10GBASE SFP+ transceivers or 1000BASE SFP transceivers. Ports 3 and 4 support only 1000BASE SFP transceivers. There are restrictions on the use of the uplink ports in both single supervisor engine and redundant supervisor engine configurations and both 10-G and 1-G operation. |
| CONSOLE port | A 10/100/1000 port that uses an RJ-45 connector. The console port allows you to access the switch either locally (with a console terminal) or through a modem (remote). The port has an RJ-45 connector. The console port allows you to perform the following functions: •Configure the switch from the CLI. •Monitor network statistics and errors. •Configure SNMP agent parameters. |
| LINK LED | The 10/100/1000 MGT port has a LINK LED associated with it. |
| Uplink port ACTIVE LEDs | Uplink ports on the supervisor engine are active in pairs. Two LEDs on the front panel show this activity. One LED, labeled 1G/10G 1-2 ACTIVE, indicates ports 1 and 2 are active; the other is labeled 1G 3-4 ACTIVE and indicates ports 3 and 4 are active. In standalone supervisor engine configurations operating in 1-Gigabit mode, all four uplink ports are active; both the 1-2 ACTIVE LED and 3-4 ACTIVE LED are lit green. In redundant supervisor engine configurations, only the 1-2 ACTIVE LED is lit green. When one supervisor engine is removed, both the 1-2 ACTIVE LED and 3-4 ACTIVE LED are lit green on the remaining supervisor engine when it is in 1-Gigabit operation. In 10-Gigabit mode, only the 1-2 ACTIVE LED is lit. |
| 10/100/1000 MGT port | The Ethernet management port is a Layer 3 host port to which you can connect a PC. You can use the Ethernet management port instead of the switch console port for network management. When managing a switch, connect the PC to the Ethernet management port on a Catalyst 4500 E-series switch. •Green—The link is operational. •Orange—The link is disabled by user. •Flashing orange—The power-on self-test indicates a faulty port. •Off—No signal is detected or there is a link configuration failure. Note When connecting a PC to the Ethernet management port, you must assign an IP address. |
| Uplink port STATUS LEDs | Uplink ports 1 and 2 each have two uplink port STATUS LEDs. The 1G LED displays port status when a 1-GB SFP transceiver is installed in the port socket. The 10G LED displays port status when a 10-GB SFP+ transceiver is installed in the port socket. Port 3 and Port 4 support only 1-GB SFP transceivers and have only the 1G port status LED. •Green—The link is operational. •Orange—The link is disabled by user. •Flashing orange—The power-on self-test indicates a faulty port. •Off—No signal is detected or there is a link configuration failure. |
| SECURE DIGITAL slot | A standard Secure Data (SD) memory card interface is provided on the front panel. |
| Uplink port LEDs | There are two types of LEDs associated with the supervisor engine uplink ports. |
Теги: WS-X45-SUP7L-E Cisco