+7 (812) 309 34 73. Договоримся!
The Huawei OptiX OSN 7500 is a new-generation optical transmission system developed by Huawei based on the current applications and development trend of MANs. It is an optical core switching (OCS) device applied to service scheduling nodes at the backbone layer of MANs to schedule and transmit services of different types and granularities.
Quick Specs
Table 1 shows the Quick Specs.
|
Product Code |
Huawei OptiX OSN 7500 |
|
Dimensions |
757 mm (H) x 497 mm (W) x 295 mm (D) |
|
Switch capacity |
Packet: 160 Gbit/s and TDM: 360 Gbit/s (higher order), 80 Gbit/s (lower order) |
|
Service slots |
22 slots for processing boards and 8 slots for interface boards |
|
Power Supply |
-48V DC/-60V DC; 110V AC/220V AC (External module) |
Product Details
Huawei OptiX OSN 7500 provides these features:
• All in One Solution Based on Universal Switch and Transport
- Unique architecture that integrates PCM, TDM, Ethernet, WDM and MPLS-TP technology.
- Universal switch at any level of packet and TDM in their original format, high efficiency and best performance, ‘0’ waste of bandwidth.
- Carefree evolution among different types of services, such as from 100% TDM to 100% packet, ‘0’ waste of investment.
• Enables optimized transport network with Built-in PCM
- Unified Access: Multiple PCM boards are developed on mature OSN serial MSTP products, realizing unified access for low-speed services.
- High Reliability: Provides direct low-speed service access, minimizing conversion equipment and fault points.
- Easy Maintenance: The NMS U2000 enables unified management, a visual interface, End-to-End (E2E) service configuration, and unified monitoring
• MPLS-TP for Highly Efficient and Highly Available Packet Transport
- Guaranteed Performance from end-to-end committed bandwidth mechanism.
- 99.999% availability: 50ms recovery for both linear and ring applications.
- SDH-like OAM mechanism capable of fast detection and troubleshooting, including end-to-end performance monitoring.
• 40G Ultra Broadband Transport
- Integrating OTU, MUX and DEMUX boards by a PID (photonics integrated device) chip, providing 40G capacity per port.
- Without complicated photonic layer design such as wavelength planning and OSNR calculating, with less patch cords and fiber operations, time to market greatly reduced.
- 50% footprint saving and 50% power consumption reduction.
• TP-Assist for Easy O&M
- MPLS-TP based O&M solution ‘TP-Assist’ providing efficient planning, fast deployment and easy maintenance, making the largescale packet network easily manageable
- Traffic based crystal clear O&M is supported with visual networklevel view, graphical format to display end-to-end service configuration, performance and status.
- Better maintenance experience even than SDH: visualized end-to-end bandwidth management, intelligently locating 92% failure, analyzable and predicable network management.
• Industrial Certifications Ensure Reliable Operation
- Compliant with EN 50121-4, IEC 61850-3, IEC 61000-6-5, IEEE 1613
Compare to Similar Items
Table 2 shows the comparison.
|
Product Code |
Huawei OptiX OSN 500 |
Huawei OptiX OSN 550 |
Huawei OptiX OSN 580 |
Huawei OptiX OSN 3500 |
Huawei OptiX OSN 7500 |
Huawei OptiX OSN 7500 II |
|
Dimensions |
44mm (H) x 442mm (W) x 220mm (D) |
88mm (H) x 442mm (W) x 220mm (D) |
221 mm (H) x 442 mm (W) x 224 mm (D) |
722 mm (H) x 497 mm (W) x 295 mm (D) |
757 mm (H) x 497 mm (W) x 295 mm (D) |
800mm (H) x 496mm (W) x 295mm (D) |
|
Switch capacity |
Packet: 7.2 Gbit/s and TDM: 21.25 Gbit/s (higher order), 5 Gbit/s (lower order) |
Packet: 64 Gbit/s ,TDM: 20 Gbit/s (higher order) |
Packet: 560 Gbit/s, TDM: 280 Gbit/s (higher order) Packet: 280 Gbit/s, TDM: 280 Gbit/s (higher order) |
Packet: 160 Gbit/s and TDM: 200 Gbit/s (higher order), 20 Gbit/s (lower order) |
Packet: 160 Gbit/s and TDM: 360 Gbit/s (higher order), 80 Gbit/s (lower order) |
Packet: 320 Gbit/s and TDM: 360 Gbit/s (higher order), 40 Gbit/s (lower order), OTN: 560Gbit/s |
|
Service slots |
3 slots |
8 slots |
15 slots |
15 slots for processing boards and 16 slots for interface boards |
22 slots for processing boards and 8 slots for interface boards |
32 slots, 16 slots for interface boards and 16 slots for processing boards with same bandwidth per slot |
|
Power Supply |
48V DC/ -60V DC, 220V AC/110V AC |
-48 V DC/-60 V DC 220 V AC/110 V AC |
-48 V DC/-60 V DC 220 V AC/110 V AC |
-48V DC/ -60V DC; 110/220V AC (External module) |
-48V DC/-60V DC; 110V AC/220V AC (External module) |
-48V DC/-60V DC |
View Overview of Huawei Transmission Network Hot Series
- Huawei OptiX OSN 1800
- Huawei OptiX OSN 500/550/580
- Huawei OptiX OSN 8800/6800/3800
- Huawei OptiX OSN 9800
- Huawei OptiX OSN 7500/7500 II
Get More Information
Do you have any question about the Huawei OptiX OSN 7500?
Contact us now via Live Chat or info@itg-spb.ru.
Huawei OptiX OSN 7500 Specification |
||
|
Dimensions |
757 mm (H) x 497 mm (W) x 295 mm (D) |
|
|
Switch capacity |
Packet: 160 Gbit/s and TDM: 360 Gbit/s (higher order), 80 Gbit/s (lower order) |
|
|
Service slots |
22 slots for processing boards and 8 slots for interface boards |
|
|
Supported interfaces |
OTN interface |
OTU-3(40G, compliant with OTL3.4 standard) |
|
Ethernet interface |
FE/GE/10GE |
|
|
SDH interface |
STM-1/4/16/64 |
|
|
PDH interface |
E1/E3/E4/T1/T3 |
|
|
ATM interface |
E1, STM-1 |
|
|
WDM interface |
40-channel DWDM interfaces, compliant with ITU-T G.694.1 8-channel CWDM interfaces, compliant with ITU-T G.694.2 |
|
|
PCM interface |
FXS/FXO, 2/4 wire audio and E&M X.21/V.35/V.11/V.24/V.28, RS232/RS422, RS449/RS423A/RS422A, RS530/RS530A, RS485, G.703 64 kbit/s codirectional |
|
|
Other interface |
DDN, SAN, Video |
|
|
Networking Mode |
Supporting pure packet, hybrid (packet + SDH) or SDH networking Supporting WDM networking Supporting single-fiber bidirectional transmission |
|
|
Power Supply |
-48V DC/-60V DC; 110V AC/220V AC (External module) |
|
|
Operation Environment |
Temperature |
Long term: -0ºC ~ 45ºC Short term: -5ºC ~ 55ºC |
|
Relative Humidity |
Long term: 5% ~ 85% Short term: 5% ~ 95% |
|
|
Ethernet Feature |
E-Line and E-LAN, QinQ MPLS-TP based VPWS and VPLS Multi-section pseudo-wire (MS-PW) ETH PWE3, TDM PWE3, ATM/IMA PWE3 IGMP Snooping V2 Blacklist, Broadcast packet suppression, ACL VLAN SWAP |
|
|
PCM features
|
Voice or data Conference/Meeting,P2MP,MP2MP FXO/FXS mode can be set by software E&M Interface voltage can be set by software (-48V/-12V) E&M signaling can be set by software (Bell types I, II, III, IV, V and British Telecom SSDC5) |
|
|
QoS |
Hierarchical QoS scheduling and traffic shaping DiffServ mode based on traffic classification, eight priority queues Simple traffic classification, complex traffic classification, per hop behavior (PHB),and ACL Committed access rate (CAR), shaping based on port scheduling priority PQ scheduling priority, weighted fair queuing (WFQ) and PQ+WFQ queuing Tail drop and weighted random early detection (WRED) |
|
|
OAM |
MPLS-TP OAM
|
LSP/PW OAM: CC, LB, LT AIS, RDI LM, DM LCK, TST CSF |
|
MPLS OAM
|
LSP/PW OAM: FDI, BDI,CV, FFD, TraceRoute, Ping, LM, DM PW OAM: CES PW VCCV |
|
|
Ethernet OAM |
ETH-CC, ETH-Loopback, ETH-Link Trace, Remote Loopback, Remote Fault Detection, RMON(RFC 2819)
|
|
|
Protection |
Equipment-level Protection
|
Cross-connect 1+1 backup, control board 1+1 backup and power 1+1 backup, clock 1+1 backup |
|
MPLS-TP based Service Protection
|
LSP/PW Linear protection, Ring protection Anti multifailure protection based on MS-PW LAG, MC-LAG, Dual-homing protection, LPT |
|
|
SDH based Service Protection |
2/4 fiber MS-SP Ring; 1+1/1:n (n<=14) Linear MSP SNCP/SNCMP/SNCTP 1:N tributary protection for E1/T1, E3/T3, E4, STM-1(e) and FE |
|
|
ASON
|
Distributed restorable rerouting protection 5-level service dedicated protection scheme based on different SLA: Diamond, Gold, Silver, Copper and Iron services Based on VC-4 and VC-12 granularity |
|
|
Synchronization
|
Both Ethernet and SDH networks supporting clock synchronization Supporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronization Adaptive clock recovery (ACR) Two external clock inputs/outputs (2 MHz or 2 Mbit/s) Two external time signals(1pps+TOD) |
|
| Характеристики | |
| -48V DC/-60V DC; 110V AC/220V AC (External module) | Operation Environment |
| 40-channel DWDM interfaces, compliant with ITU-T G.694.18-channe | PCM interface |
| ASON | Distributed restorable rerouting protection5-level service dedicated protection scheme based on different SLA: Diamond, Gold, Silver, Copper and Iron servicesBased on VC-4 and VC-12 granularity |
| DDN, SAN, Video | Networking Mode |
| Dimensions | 757 mm (H) x 497 mm (W) x 295 mm (D) |
| E1, STM-1 | WDM interface |
| E1/E3/E4/T1/T3 | ATM interface |
| Equipment-level Protection | Cross-connect 1+1 backup, control board 1+1 backup and power 1+1 backup, clock 1+1 backup |
| ETH-CC, ETH-Loopback, ETH-Link Trace, Remote Loopback, Remote Fa | Protection |
| Ethernet Feature | E-Line and E-LAN, QinQMPLS-TP based VPWS and VPLSMulti-section pseudo-wire (MS-PW)ETH PWE3, TDM PWE3, ATM/IMA PWE3IGMP Snooping V2Blacklist, Broadcast packet suppression, ACLVLAN SWAP |
| FE/GE/10GE | SDH interface |
| FXS/FXO, 2/4 wire audio and E&MX.21/V.35/V.11/V.24/V.28, RS2 | Other interface |
| LSP/PW OAM: FDI, BDI,CV, FFD, TraceRoute, Ping, LM, DMPW OAM: CE | Ethernet OAM |
| LSP/PW OAM:CC, LB, LTAIS, RDILM, DMLCK, TSTCSF | MPLS OAM |
| MPLS-TP based Service Protection | LSP/PW Linear protection, Ring protectionAnti multifailure protection based on MS-PWLAG, MC-LAG, Dual-homing protection, LPT |
| OAM | MPLS-TP OAM |
| OTU-3(40G, compliant with OTL3.4 standard) | Ethernet interface |
| PCM features | Voice or data Conference/Meeting,P2MP,MP2MPFXO/FXS mode can be set by softwareE&M Interface voltage can be set by software (-48V/-12V)E&M signaling can be set by software (Bell types I, II, III, IV, V and British Telecom SSDC5) |
| QoS | Hierarchical QoS scheduling and traffic shapingDiffServ mode based on traffic classification, eight priority queuesSimple traffic classification, complex traffic classification, per hop behavior (PHB),and ACLCommitted access rate (CAR), shaping based on port scheduling priorityPQ scheduling priority, weighted fair queuing (WFQ) and PQ+WFQ queuingTail drop and weighted random early detection (WRED) |
| Relative humidity | Long term: 5% ~ 85%Short term: 5% ~ 95% |
| SDH based Service Protection | 2/4 fiber MS-SP Ring;1+1/1:n (n<=14) Linear MSPSNCP/SNCMP/SNCTP1:N tributary protection for E1/T1, E3/T3, E4, STM-1(e) and FE |
| Service Slots | 22 slots for processing boards and 8 slots for interface boards |
| STM-1/4/16/64 | PDH interface |
| Supported interfaces | OTN interface |
| Supporting pure packet, hybrid (packet + SDH) or SDH networkingS | Power Supply |
| Switch capacity | Packet: 160 Gbit/s and TDM: 360 Gbit/s (higher order), 80 Gbit/s (lower order) |
| Synchronization | Both Ethernet and SDH networks supporting clock synchronizationSupporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronizationAdaptive clock recovery (ACR)Two external clock inputs/outputs (2 MHz or 2 Mbit/s)Two external time signals(1pps+TOD) |
| Temperature | Long term: -0ºC ~ 45ºC Short term: -5ºC ~ 55ºC |