+7 (812) 309 34 73. Договоримся!
P04662-B21 is the HPE ProLiant DL325 Gen10 NVMe SFF Configure-to-order Server. The HPE ProLiant DL325 Gen10 Server is the secure and versatile single socket server for virtualization and I/O intensive workloads. This 1P, 1U server delivers and exceptional balance of processor, memory and I/O for 2P performance at 1P TCO. Get the most out of your virtualized environment with this versatile server.
Quick Spec
Table 1 shows the quick spec.
|
SKU Number |
P04662-B21 |
|
Description |
HPE ProLiant DL325 Gen10 NVMe SFF CTO Server |
|
Processor |
Not included as standard |
|
DIMM Slots |
16-DIMM slots |
|
Storage Controller |
Choice of HPE modular Smart Array and PCIe plug-in controller |
|
PCIe |
Two standard in primary riser |
|
Drive Cage - included |
8 SFF NVMe |
|
Network Controller |
HPE 1Gb Ethernet 4-Port 331i Adapter plus optional HPE FlexibleLOM or stand up card |
|
Fans |
7-Performance |
|
Management |
HPE iLO with Intelligent Provisioning (standard), iLO Advances and OneView (optional) |
|
USB |
Front: 1 USB 3.0 + iLO service port Rear: 2 USB 3.0 Internal: 1 USB 3.0 |
Product Details
Figure 1 shows the HPE DL325 Gen10 server NVMe SFF Front View (10 SFF NVMe Shown).
Note:
|
① |
Quick removal access panel |
⑥ |
USB 3.0 port |
|
② |
Serial no. label pull tab |
⑦ |
NIC status LED |
|
③ |
Optional Media Bay |
⑧ |
iLO Service Port |
|
④ |
Power On/Standby button and system power LED |
⑨ |
UID button/LED |
|
⑤ |
Health LED |
⑩ |
Standard 8 NVMe drive bays |
Figure 2 shows the rear view of HPE DL325 Gen10 server.
Note:
|
① |
Slot 1 PCIe 3.0 |
⑦ |
iLO Management Port |
|
② |
Slot 2 PCIe 3.0 |
⑧ |
UID LED |
|
③ |
Optional Slot 3 PCIe 3.0 |
⑨ |
Embedded 4x 1GbE Adapter |
|
④ |
HPE Flexible Slot Power Supply Bay |
⑩ |
VGA Port |
|
⑤ |
HPE Flexible Slot Power Supply Bay |
⑪ |
Option: FlexibleLOM (Shown: 4x 1GbE) |
|
⑥ |
USB 3.0 Ports |
|
|
Configuration Information
This section lists some of the steps required to configure a Factory Integrated Model. To ensure only valid configurations are ordered, Hewlett Packard Enterprise recommends the use of an HPE approved configurator. Contact your local sales representative for information on configurable product offerings and requirements.
1. Factory Integrated Models must start with a CTO Server.
2. FIO indicates that this option is only available as a factory installable option.
3. All Factory Integrated Models will be populated with sufficient hard drive blanks based on the number of initial hard drives ordered with the server.
4. Some options may not be integrated at the factory. Contact our sales team for additional information.
Step 1: Base Configuration (choose one of the following configurable models)
|
CTO Server |
HPE ProLiant DL325 Gen10 4 LFF CTO Server |
HPE ProLiant DL325 Gen10 8 SFF CTO Server |
HPE ProLiant DL325 Gen10 NVMe SFF CTO Server |
|
SKU Number |
P04653-B21 |
P04654-B21 |
P04662-B21 |
|
TAA SKU |
P04652-B21 |
P04848-B21 |
P05046-B21 |
|
Processor |
Not included as standard |
Not included as standard |
Not included as standard |
|
DIMM Slots |
16-DIMM slots |
16-DIMM slots |
16-DIMM slots |
|
Storage Controller |
Choice of HPE modular Smart Array and PCIe plug-in controller |
||
|
PCIe |
Two standard in primary riser |
||
|
Drive Cage - included |
4 LFF |
8 SFF |
8 SFF NVMe |
|
Network Controller |
HPE 1Gb Ethernet 4-Port 331i Adapter plus optional HPE FlexibleLOM or stand up card |
||
|
Fans |
5-Standard |
5-Performance |
7-Performance |
|
Management |
HPE iLO with Intelligent Provisioning (standard), iLO Advances and OneView (optional) |
||
|
USB |
Front: 1 USB 3.0 + iLO service port Rear: 2 USB 3.0 Internal: 1 USB 3.0 |
Front: 1 USB 3.0 + iLO service port Rear: 2 USB 3.0 Internal: 1 USB 3.0 |
Front: 1 USB 3.0 + iLO service port Rear: 2 USB 3.0 Internal: 1 USB 3.0 |
|
CTO Server |
8 SFF CTO Chassis |
4 LFF CTO Chassis |
NVMe SFF CTO Chassis |
|
Included Drive Cage |
8 SFF SAS/SATA |
4 LFF + UMB |
8 NVMe Chassis |
|
Additional drive cages |
- |
- |
- |
|
Universal Media Bay |
1 Optional |
1 Included |
1 Optional |
|
ODD |
1 Optional with UMB |
1 Optional |
1 Optional with UMB |
|
2 SFF SAS/SATA |
1 Optional |
Not available |
1 Optional |
|
2 SFF NVMe |
1 Optional |
Not available |
1 Optional |
Step 2a: Choose Required Options – Processors
(only one of the following unless otherwise noted)
Please select one –L21 processor required below.
NOTE: All CTO Models ship with redundant fan configuration.
NOTE: DDR4 memory speed will depend on the quantity and type of DIMMs installed.
NOTE: Processors with greater than 170W will ship with the High Performance heatsink.
|
Processor Option Kits |
Required Processor |
|
HPE DL325 Gen10 AMD EPYC 7601 (2.2GHz/32-core/180W) FIO Processor Kit |
P04851-L21 |
|
HPE DL325 Gen10 AMD EPYC 7551P (2.0 GHz/32-core/180W) FIO Processor Kit |
P04852-L21 |
|
HPE DL325 Gen10 AMD EPYC 7501 (2.0GHz/32-core/155-170W) FIO Processor Kit |
P04853-L21 |
|
HPE DL325 Gen10 AMD EPYC 7451 (2.3GHz/24-core/180W) FIO Processor Kit |
P04854-L21 |
|
HPE DL325 Gen10 AMD EPYC 7401P (2.0GHz/24-core/155-170W) FIO Processor Kit |
P04855-L21 |
|
HPE DL325 Gen10 AMD EPYC 7351P (2.4GHz/16-core/155-170W) FIO Processor Kit |
P04856-L21 |
|
HPE DL325 Gen10 AMD EPYC 7301 (2.2GHz/16-core/155-170W) FIO Processor Kit |
P04857-L21 |
|
HPE DL325 Gen10 AMD EPYC 7281 (2.1GHz/16-core/155-170W) FIO Processor Kit |
P04858-L21 |
|
HPE DL325 Gen10 AMD EPYC 7261 (2.5GHz/8-core/155-170W) FIO Processor Kit |
P05918-L21 |
|
HPE DL325 Gen10 AMD EPYC 7251 (2.1GHz/8-core/120W) FIO Processor Kit |
P04859-L21 |
Step 2b: Choose Memory Options
Please select one or more memory from below.
|
Registered DIMMs (RDIMMs) |
|
|
HPE 8GB (1x8GB) Single Rank x8 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit |
838079-B21 |
|
HPE 16GB (1x16GB) Dual Rank x8 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit |
838089-B21 |
|
HPE 32GB (1x32GB) Dual Rank x4 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit |
838083-B21 |
|
HPE 64GB (1x64GB) Dual Rank x4 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit |
P05592-B21 |
|
HPE 16GB (1x16GB) Single Rank x4 DDR4-2666 CAS-19-19-19 Registered Smart Memory Kit |
838081-B21 |
|
HPE 64GB (1x64GB) Quad Rank x4 DDR4-2666 CAS-19-19-19 Load Reduced Smart Memory Kit |
838085-B21 |
|
HPE 128GB (1x128GB) Octal Rank x4 DDR4-2666 CAS-22-19-19 3DS Load Reduced Smart Memory Kit |
838087-B21 |
Step 2c: Choose Power Supplies
Select one or two power supplies from below.
NOTE: Mixing of 2 different power supplies is NOT allowed.
|
HPE ProLiant Gen10 Entry Level Server Power Supplies – Non-Redundant |
|
|
HPE 500W Low Halogen FIO Power Supply Kit |
837074-B21 |
|
NOTE: This is a Factory Installed Option (FIO) only. NOTE: Supports Gold-level efficiency (92%) with a standard C14 inlet connector. No support for HPE Power Discovery Services. |
|
|
HPE ProLiant Gen10 Flexible Slot Power Supplies – Redundant |
|
|
NOTE: HPE DL325 Gen10 Redundant Power Supply Enablement Kit (P04983-B21) is mandatory to use any of the following power supplies. |
|
|
HPE 500W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit |
865408-B21 |
|
HPE 800W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit |
865414-B21 |
|
HPE 800W Flex Slot Titanium Hot Plug Low Halogen Power Supply Kit |
865438-B21 |
|
HPE 800W Flex Slot -48VDC Hot Plug Low Halogen Power Supply Kit |
865434-B21 |
|
HPE 1600W Flex Slot Platinum Hot Plug Low Halogen Power Supply Kit |
830272-B21 |
|
HPE 800W Flex Slot Universal Hot Plug Low Halogen Power Supply Kit |
865428-B21 |
Step 3: Choose Additional Factory Integratable Options
One of the following from each list may be selected if desired at time of factory integration
|
HPE Unique Options |
|
|
HPE DL325 Gen10 2SFF Smart Array SAS FIO Cable Kit |
P05036-B21 |
|
NOTE: Required to connect the 2SFF FIO Enablement Kit (881179-B21) to E208i-a or P408i-a controller. |
|
|
HPE DL325 Gen10 8SFF Embedded SATA Controller FIO Cable Kit |
P05030-B21 |
|
NOTE: Used with the 8SFF CTO to connect to the embedded SATA controller on mother board. NOTE: The embedded SATA controller works only in the AHCI mode and does not support SW RAID. |
|
|
HPE DL325 Gen10 2SFF Embedded SATA Controller FIO Cable Kit |
P05039-B21 |
|
NOTE: Used with the 2SFF SAS/SATA FIO Enablement Kit to connect to the embedded SATA controller on mother board. NOTE: The embedded SATA controller works only in the AHCI mode and does not support SW RAID. |
|
|
HPE 1U Gen10 4LFF Embedded SATA Controller FIO Cable Kit |
866444-B21 |
|
NOTE: Used with the 4LFF CTO to connect to the embedded SATA controller on mother board. NOTE: The embedded SATA controller works only in the AHCI mode and does not support SW RAID |
|
|
HPE 1U Gen10 2SFF SAS/SATA FIO Enablement Kit without Cables |
881179-B21 |
|
NOTE: This option can be selected only on 8SFF CTO or NVMe SFF CTO. NOTE: This option kit will enable 2SFF SAS/SATA drives. |
|
|
HPE Security |
|
|
HPE Gen10 TPM 1.2 FIO Setting |
872108-B21 |
|
NOTE: HPE Trusted Platform Module 2.0 Gen10 Option (864279-B21), if it needs to be operated in TPM 1.2 Mode. |
|
|
BIOS Mode |
|
|
HPE Legacy FIO Mode Setting |
758959-B22 |
|
NOTE: UEFI is the default, this FIO part can be used for CTO to enable Legacy mode. |
|
|
HPE Converged Infrastructure Management Software |
|
|
HPE OneView w/o iLO including 3yr 24x7 Support 1-server FIO LTU |
P8B31A |
Step 4: Choose additional options for Factory Integration from Core and Additional Options sections via datasheet.
Get More Information
Do you have any question about the P04662-B21?
Contact us now via Live Chat or info@itg-spb.ru.
P04662-B21 Specification |
|
|
Description |
HPE ProLiant DL325 Gen10 NVMe SFF CTO Server |
|
Processor |
Not included as standard |
|
DIMM Slots |
16-DIMM slots |
|
Storage Controller |
Choice of HPE modular Smart Array and PCIe plug-in controller |
|
PCIe |
Two standard in primary riser |
|
Drive Cage - included |
8 SFF NVMe |
|
Network Controller |
HPE 1Gb Ethernet 4-Port 331i Adapter plus optional HPE FlexibleLOM or stand up card |
|
Fans |
7-Performance |
|
Management |
HPE iLO with Intelligent Provisioning (standard), iLO Advances and OneView (optional) |
|
USB |
Front: 1 USB 3.0 + iLO service port Rear: 2 USB 3.0 Internal: 1 USB 3.0 |
|
Dimensions |
4.29 x 43.46 x 61.49 cm 1.69 x 17.11 x 24.21 in |
|
Input Requirements |
Rated Line Voltage: 100 to 120 VAC 200 to 240 VAC |
|
BTU Rating |
Maximum: For 800W Power Supply: 3207 BTU/hr (at 100 VAC), 3071 BTU/hr (at 200 VAC), 3112 BTU/hr (at 240 VAC) for China Only
For 500W Power Supply: 1979 BTU/hr (at 100 VAC), 1911 BTU/hr (at 200 VAC), 1965 BTU/hr (at 240 VAC) for China Only |
| Характеристики | |
| BTU Rating | Maximum:For 800W Power Supply: 3207 BTU/hr (at 100 VAC), 3071 BTU/hr (at 200 VAC), 3112 BTU/hr (at 240 VAC) for China Only For 500W Power Supply: 1979 BTU/hr (at 100 VAC), 1911 BTU/hr (at 200 VAC), 1965 BTU/hr (at 240 VAC) for China Only |
| Description | HPE ProLiant DL325 Gen10 NVMe SFF CTO Server |
| Dimensions | 4.29 x 43.46 x 61.49 cm1.69 x 17.11 x 24.21 in |
| DIMM Slots | 16-DIMM slots |
| Drive Cage - included | 8 SFF NVMe |
| Fans | 7-Performance |
| Input Requirements (per power supply) | Rated Line Voltage:100 to 120 VAC200 to 240 VAC |
| Management | HPE iLO with Intelligent Provisioning (standard), iLO Advances and OneView (optional) |
| Network Controller | HPE 1Gb Ethernet 4-Port 331i Adapter plus optional HPE FlexibleLOM or stand up card |
| PCIe | Two standard in primary riser |
| Processor | Not included as standard |
| Storage controller | Choice of HPE modular Smart Array and PCIe plug-in controller |
| USB | Front: 1 USB 3.0 + iLO service portRear: 2 USB 3.0Internal: 1 USB 3.0 |
Теги: P04662-B21 HPE